15 questions0 / 15 done
- 1ME 2024 · 1 mark · MCQ · EasyFor a ball bearing, the fatigue life in millions of revolutions is given by L=(PC)n, where P is the constant applied load and C is the basic dynamic load rating. Which one of the following statements is TRUE?
- 2ME 2024 · 1 mark · MCQ · ModerateThe change in kinetic energy ΔE of an engine is 300J, and minimum and maximum shaft speeds are ωmin=220rad/s and ωmax=280rad/s, respectively. Assume that the torque-time function is purely harmonic. To achieve a coefficient of fluctuation of 0.05, the moment of inertia (in kg.m2) of the flywheel to be mounted on the engine shaft is
- 3ME 2024 · 1 mark · MCQ · ModerateA ram in the form of a rectangular body of size l=9m and b=2m is suspended by two parallel ropes of lengths 7m. Assume the center-of-mass of the body is at its geometric center and g=9.81m/s2. For striking the object P with a horizontal velocity of 5m/s, what is the angle θ with the vertical from which the ram should be released from rest?
- 4ME 2024 · 1 mark · MCQ · ModerateA linear spring-mass-dashpot system with a mass of 2kg is set in motion with viscous damping. If the natural frequency is 15Hz, and the amplitudes of two successive cycles measured are 7.75mm and 7.20mm, the coefficient of viscous damping (in N.s/m) is
- 5ME 2024 · 1 mark · MCQ · EasyWhich one of the following failure theories is the most conservative design approach against fatigue failure?
- 6ME 2024 · 1 mark · MCQ · ModerateA rigid massless tetrahedron is placed such that vertex O is at the origin and the other three vertices A, B, and C lie on the coordinate axes as shown in the figure. The body is acted on by three point loads, of which one is acting at A along x-axis and another at point B along y-axis. For the body to be in equilibrium, the third point load acting at point O must be
- 7ME 2024 · 2 marks · MSQ · EasyWhich of the following beam(s) is/are statically indeterminate?
- 8ME 2024 · 2 marks · NAT · HardThe Levai type-A train illustrated in the figure has gears with module m=8mm/tooth. Gears 2 and 3 have 19 and 24 teeth respectively. Gear 2 is fixed and internal gear 4 rotates at 20rev/min counter-clockwise. The magnitude of angular velocity of the arm is ____ rev/min. (rounded off to 2 decimal places)
- 9ME 2024 · 2 marks · NAT · ModerateA horizontal beam of length 1200mm is pinned at the left end and is resting on a roller at the other end as shown in the figure. A linearly varying distributed load is applied on the beam. The magnitude of maximum bending moment acting on the beam is ____ N.m. (round off to 1 decimal place)
- 10ME 2024 · 2 marks · NAT · ModerateAt the instant when OP is vertical and AP is horizontal, the link OD is rotating counter clockwise at a constant rate ω=7rad/s. Pin P on link OD slides in the slot BC of link ABC which is hinged at A, and causes a clockwise rotation of the link ABC. The magnitude of angular velocity of link ABC for this instant is ____ rad/s (rounded off to 2 decimal places).
- 11ME 2024 · 2 marks · NAT · ModerateA vibratory system consists of mass m, a vertical spring of stiffness 2k and a horizontal spring of stiffness k. The end A of the horizontal spring is given a horizontal motion xA=asinωt. The other end of the spring is connected to an inextensible rope that passes over two massless pulleys as shown. Assume m=10kg, k=1.5kN/m, and neglect friction. The magnitude of critical driving frequency for which the oscillations of mass m tend to become excessively large is ____ rad/s (answer in integer).
- 12ME 2024 · 2 marks · NAT · ModerateA solid massless cylindrical member of 50mm diameter is rigidly attached at one end, and is subjected to an axial force P=100kN and a torque T=600N. m at the other end as shown. Assume that the axis of the cylinder is normal to the support. Considering distortion energy theory with allowable yield stress as 300MPa, the factor of safety in the design is ____ (rounded off to 1 decimal place).
- 13ME 2024 · 2 marks · NAT · ModerateThe figure shows a thin cylindrical pressure vessel constructed by welding plates together along a line that makes an angle α=60∘ with the horizontal. The closed vessel has a wall thickness of 10mm and diameter of 2m. When subjected to an internal pressure of 200kPa, the magnitude of the normal stress acting on the weld is ____ MPa (rounded off to 1 decimal place).
- 14ME 2024 · 2 marks · NAT · ModerateA three-hinge arch ABC in the form of a semi-circle is shown in the figure. The arch is in static equilibrium under vertical loads of P=100kN and Q=50kN. Neglect friction at all the hinges. The magnitude of the horizontal reaction at B is ____ kN (rounded off to 1 decimal place).
- 15ME 2024 · 2 marks · NAT · ModerateA band brake shown in the figure has a coefficient of friction of 0.3. The band can take a maximum force of 1.5kN. The maximum braking force (F) that can be safely applied is ____ N (rounded off to the nearest integer).