- 1Aptitude · 1 mark · MCQ · EasyThis book, including all its chapters,____ interesting. The students as well as the instructor____ in agreement about it.
- 2Aptitude · 1 mark · MCQ · EasyPeople were prohibited ____ their vehicles near the entrance of the main administrative building.
- 3Aptitude · 1 mark · MCQ · EasySelect the word that fits the analogy:
- 4Aptitude · 1 mark · MCQ · EasyStock markets ____ at the news of the coup.
- 5Aptitude · 1 mark · MCQ · ModerateIf P,Q,R,S are four individuals, how many teams of size exceeding one can be formed, with Q as a member?
- 7Aptitude · 2 marks · MCQ · ModerateSelect the next element of the series: Z, WV, RQP, ____
- 8Aptitude · 2 marks · MCQ · ModerateIn four-digit integer numbers from 1001 to 9999, the digit group "37" (in the same sequence) appears ____ times.
- 9Aptitude · 2 marks · MCQ · ModerateGiven a semicircle with O as the centre, as shown in the figure, the ratio ABAC+CB is _____, where AC, CB and AB are chords.
- 10Aptitude · 2 marks · MCQ · ModerateThe revenue and expenditure of four different companies P, Q, R and S in 2015 are shown in the figure. If the revenue of company Q in 2015 was 20% more than that in 2014, and company Q had earned a profit of 10% on expenditure in 2014, then its expenditure (in million rupees) in 2014 was _____.
- 111 mark · MCQ · Hardax3+bx2+cx+d is a polynomial on real x over real coefficients a,b,c,d
wherein a=0. Which of the following statements is true?
- 121 mark · MCQ · ModerateWhich of the following is true for all possible non-zero choices of integers m,n;m=n, or all possible non-zero choices of real numbers p,q;p=q, as applicable?
- 131 mark · MCQ · ModerateWhich of the following statements is true about the two sided Laplace transform?
- 141 mark · MCQ · ModerateConsider a signal x[n]=(21)n1[n], where 1[n]=0 if n<0, and 1[n]=1 if n≥0. The z-transform of x[n−k],k>0 is 1−21z−1z−k with region of convergence being
- 151 mark · MCQ · ModerateThe value of the following complex integral, with C representing the unit circle centered at origin in the counterclockwise sense, is:
- 161 mark · MCQ · EasyxR and xA are, respectively, the rms and average values of x(t)=x(t−T), and similarly, yR and yA are, respectively, the rms and average values of y(t)=kx(t). k,T are independent of t. Which of the following is true?
- 171 mark · MCQ · ModerateA three-phase cylindrical rotor synchronous generator has a synchronous reactance Xs and a negligible armature resistance. The magnitude of per phase terminal voltage is VA and the magnitude of per phase induced emf is EA. Considering the following two statements, P and Q,
- 181 mark · MCQ · ModerateA lossless transmission line with 0.2 pu reactance per phase uniformly distributed along the length of the line, connecting a generator bus to a load bus, is protected up to 80 % of its length by a distance relay placed at the generator bus. The generator terminal voltage is 1 pu. There is no generation at the load bus. The threshold pu current for operation of the distance relay for a solid three phase-to-ground fault on the transmission line is closest to:
- 191 mark · MCQ · EasyOut of the following options, the most relevant information needed to specify the
real power (P) at the PV buses in a load flow analysis is
- 201 mark · MCQ · EasyConsider a linear time-invariant system whose input r(t) and output y(t) are
related by the following differential equation:
- 211 mark · MCQ · ModerateA single-phase, full-bridge diode rectifier fed from a 230V, 50Hz sinusoidal source supplies a series combination of finite resistance, R, and a very large inductance, L. The two most dominant frequency components in the source current are:
- 221 mark · MCQ · ModerateThyristor T1 is triggered at an angle α (in degree), and T2 at angle 180∘+α, in each cycle of the sinusoidal input voltage. Assume both thyristors to be ideal. To control the load power over the range 0 to 2kW, the minimum range of variation in α is:
- 231 mark · MCQ · EasyWhich of the options is an equivalent representation of the signal flow graph shown here?
- 241 mark · MCQ · EasyA common-source amplifier with a drain resistance, RD=4.7kΩ, is powered using a 10V power supply. Assuming that the transconductance, gm, is 520μA/V, the voltage gain of the amplifier is closest to:
- 251 mark · MCQ · ModerateA sequence detector is designed to detect precisely 3 digital inputs, with overlapping sequences detectable. For the sequence (1,0,1) and input data (1,1,0,1,0,0,1,1,0,1,0,1,1,0), what is the output of this detector?
- 261 mark · NAT · ModerateConsider the initial value problem below. The value of y at x=ln2, (rounded off to 3 decimal places) is ________.
- 271 mark · NAT · ModerateA three-phase, 50Hz, 4-pole induction motor runs at no-load with a slip of 1%.
- 281 mark · NAT · EasyCurrents through ammeters A2 and A3 in the figure are 1∠10∘ and 1∠70∘, respectively. The reading of the ammeter A1 (rounded off to 3 decimal places) is ____ A.
- 291 mark · NAT · ModerateThe Thevenin equivalent voltage, VTH, in V (rounded off to 2 decimal places) of the network shown below, is _______
- 311 mark · NAT · ModerateA single-phase, 4kVA, 200V/100V, 50Hz transformer with laminated CRGO steel core has rated no-load loss of 450W. When the high-voltage winding is excited with 160V, 40Hz sinusoidal ac supply, the no-load losses are found to be 320W. When the high-voltage winding of the same transformer is supplied from a 100V, 25Hz sinusoidal ac source, the no-load losses will be _____ W (rounded off to 2 decimal places).
- 321 mark · NAT · ModerateA single-phase inverter is fed from a 100V dc source and is controlled using a quasi-square wave modulation scheme to produce an output waveform, v(t), as shown. The angle σ is adjusted to entirely eliminate the 3rd harmonic component from the output voltage. Under this condition, for v(t), the magnitude of the 5th harmonic component as a percentage of the magnitude of the fundamental component is ____ (rounded off to 2 decimal places).
- 331 mark · NAT · ModerateA single 50Hz synchronous generator on droop control was delivering 100MW power to a system. Due to increase in load, generator power had to be increased by 10MW, as a result of which, system frequency dropped to 49.75Hz. Further increase in load in the system resulted in a frequency of 49.25Hz. At this condition, the power in MW supplied by the generator is ____ (rounded off to 2 decimal places).
- 362 marks · MCQ · ModerateFor real numbers, x and y, with y=3x2+3x+1, the maximum and minimum value of y for x∈[−2,0] are respectively. ____.
- 372 marks · MCQ · EasyThe vector function expressed by
- 382 marks · MCQ · ModerateA 250V dc shunt motor has an armature resistance of 0.2Ω and a field resistance of 100Ω. When the motor is operated on no-load at rated voltage, it draws an armature current of 5A and runs at 1200rpm. When a load is coupled to the motor, it draws total line current of 50A at rated voltage, with a 5% reduction in the air-gap flux due to armature reaction. Voltage drop across the brushes can be taken as 1V per brush under all operating conditions. The speed of the motor, in rpm, under this loaded condition, is closest to:
- 392 marks · MCQ · ModerateTwo buses, i and j, are connected with a transmission line of admittance Y, at the two ends of which there are ideal transformers with turns ratios as shown. Bus admittance matrix for the system is:
- 402 marks · MCQ · ModerateConsider the diode circuit shown below. The diode, D, obeys the current-voltage characteristic ID=IS(exp(nVTVD)−1), where n>1, VT>0. VD is the voltage across the diode and ID is the current through it. The circuit is biased so that voltage, V>0 and current, I<0. If you had to design this circuit to transfer maximum power from the current source (I1) to a resistive load (not shown) at the output, what values of R1 and R2 would you choose?
- 412 marks · MCQ · HardA non-ideal diode is biased with a voltage of −0.03V, and a diode current of I1 is measured. The thermal voltage is 26mV and the ideality factor for the diode is 15/13. The voltage, in V, at which the measured current increases to 1.5I1 is closest to:
- 422 marks · MCQ · ModerateA benchtop dc power supply acts as an ideal 4A current source as long as its terminal voltage is below 10V. Beyond this point, it begins to behave as an ideal 10V voltage source for all load currents going down to 0A. When connected to an ideal rheostat, find the load resistance value at which maximum power is transferred, and the corresponding load voltage and current.
- 432 marks · MCQ · ModerateThe static electric field inside a dielectric medium with relative permittivity, εr=2.25, expressed in cylindrical coordinate system is given by the following expression
- 442 marks · MCQ · ModerateConsider a permanent magnet dc (PMDC) motor which is initially at rest. At t=0, a dc voltage of 5V is applied to the motor. Its speed monotonically increases from 0rad/s to 6.32rad/s in 0.5s and finally settles to 10rad/s. Assuming that the armature inductance of the motor is negligible, the transfer function for the motor is
- 452 marks · MCQ · ModerateWhich of the following options is correct for the system shown below?
- 462 marks · MCQ · EasyConsider a negative unity feedback system with the forward path transfer function
- 472 marks · MCQ · ModerateSuppose for input x(t) a linear time-invariant system with impulse response h(t) produces output y(t), so that x(t)∗h(t)=y(t). Further, if ∣x(t)∣∗∣h(t)∣=z(t), which of the following statements is true?
- 482 marks · MCQ · ModerateThe causal realization of a system transfer function H(s) having poles at
(2,−1),(−2,1) and zeroes at (2,1),(−2,−1) will be
- 492 marks · MCQ · ModerateWhich of the following options is true for a linear time-invariant discrete time
system that obeys the difference equation:
y[n]−ay[n−1]=b0x[n]−b1x[n−1]
- 502 marks · MCQ · ModerateLet ar, aϕ and az be unit vectors along r, ϕ and z directions, respectively in the cylindrical coordinate system. For the electric flux density given by D=(ar15+aϕ2r−az3rz)Coulomb/m2, the total electric flux, in Coulomb, emanating from the volume enclosed by a solid cylinder of radius 3m and height 5m oriented along the z-axis with its base at the origin is:
- 512 marks · MCQ · ModerateA stable real linear time-invariant system with single pole at p, has a transfer function H(s)=s−ps2+100 with a dc gain of 5. The smallest positive frequency, in rad/s, at unity gain is closest to:
- 522 marks · MCQ · HardThe number of purely real elements in a lower triangular representation of the given 3×3 matrix, obtained through the given decomposition is ____.
- 532 marks · MCQ · ModerateThe figure below shows the per-phase Open Circuit Characteristics (measured in V) and Short Circuit Characteristics (measured in A) of a 14kVA, 400V, 50Hz, 4-pole, 3-phase, delta connected alternator, driven at 1500rpm. The field current, If is measured in A. Readings taken are marked as respective (x,y) coordinates in the figure. Ratio of the unsaturated and saturated synchronous impedances (Zs(unsat)/Zs(sat)) of the alternator is closest to:
- 542 marks · NAT · EasyLet ax and ay be unit vectors along x and y directions, respectively. A vector function is given by
- 552 marks · NAT · ModerateA resistor and a capacitor are connected in series to a 10V dc supply through a switch. The switch is closed at t=0, and the capacitor voltage is found to cross 0V at t=0.4τ, where τ is the circuit time constant. The absolute value of percentage change required in the initial capacitor voltage if the zero crossing has to happen at t=0.2τ is _____ (rounded off to 2 decimal places).
- 572 marks · NAT · ModerateBus 1 with voltage magnitude V1=1.1pu is sending reactive power Q12 towards bus 2 with voltage magnitude V2=1pu through a lossless transmission line of reactance X. Keeping the voltage at bus 2 fixed at 1pu, magnitude of voltage at bus 1 is changed, so that the reactive power Q12 sent from bus 1 is increased by 20%. Real power flow through the line under both the conditions is zero. The new value of the voltage magnitude, V1, in pu (rounded off to 2 decimal places), at bus 1 is ____.
- 592 marks · NAT · ModerateA cylindrical rotor synchronous generator has steady state synchronous reactance of 0.7pu and subtransient reactance of 0.2pu. It is operating at (1+j0)pu terminal voltage with an internal emf of (1+j0.7)pu. Following a three-phase solid short circuit fault at the terminal of the generator, the magnitude of the subtransient internal emf (rounded off to 2 decimal places) is ________ pu.
- 602 marks · NAT · ModerateIn the dc-dc converter circuit shown, switch Q is switched at a frequency of 10kHz with a duty ratio of 0.6. All components of the circuit are ideal, and the initial current in the inductor is zero. Energy stored in the inductor in mJ (rounded off to 2 decimal places) at the end of 10 complete switching cycles is ________.
- 612 marks · NAT · ModerateA single-phase, full-bridge, fully controlled thyristor rectifier feeds a load comprising a 10Ω resistance in series with a very large inductance. The rectifier is fed from an ideal 230V, 50Hz sinusoidal source through cables which have negligible internal resistance and a total inductance of 2.28mH. If the thyristors are triggered at an angle α=45∘, the commutation overlap angle in degree (rounded off to 2 decimal places) is ____.
- 622 marks · NAT · ModerateA non-ideal Si-based pn junction diode is tested by sweeping the bias applied across its terminals from −5V to +5V. The effective thermal voltage, VT, for the diode is measured to be (29±2)mV. The resolution of the voltage source in the measurement range is 1mV. The percentage uncertainty (rounded off to 2 decimal places) in the measured current at a bias voltage of 0.02V is ____.
- 642 marks · NAT · ModerateAn 8085 microprocessor accesses two memory locations (2001H) and (2002H), that contain 8-bit numbers 98H and B1H, respectively. The following program is executed:
- 652 marks · NAT · ModerateA conducting square loop of side length 1m is placed at a distance of 1m from a long straight wire carrying a current I=2A as shown below. The mutual inductance, in nH (rounded off to 2 decimal places), between the conducting loop and the long wire is ________.