- 1Aptitude · 1 mark · MCQ · Easy"Since you have gone off the _____, the _____ sand is likely to damage the car."
- 2Aptitude · 1 mark · MCQ · Easy"A common misconception among writers is that sentence structure mirrors thought; the more ____ the structure, the more complicated the ideas."
- 3Aptitude · 1 mark · MCQ · EasyThe three roots of the equation f(x)=0 are x={−2,0,3}. What are the three values of x for which f(x−3)=0?
- 4Aptitude · 1 mark · MCQ · ModerateFor what values of k given below is k−3(k+2)2 an integer?
- 5Aptitude · 1 mark · MCQ · EasyFunctions F(a,b) and G(a,b) are defined as follows:
F(a,b)=(a−b)2 and G(a,b)=∣a−b∣, where ∣x∣ represents the absolute value of x.
What would be the value of G(F(1,3),G(1,3))?
- 6Aptitude · 2 marks · MCQ · ModerateAn e-mail password must contain three characters. The password has to contain one numeral from 0 to 9, one upper case and one lower case character from the English alphabet. How many distinct passwords are possible?
- 7Aptitude · 2 marks · MCQ · EasyIn a certain code, AMCF is written as EQQJ and NKUF is written as ROYJ. How will DHLP be written in that code?
- 8Aptitude · 2 marks · MCQ · ModerateA class of twelve children has two more boys than girls. A group of three children are randomly picked from this class to accompany the teacher on a field trip. What is the probability that the group accompanying the teacher contains more girls than boys?
- 9Aptitude · 2 marks · MCQ · ModerateA designer uses marbles of four different colours for his designs. The cost of each marble is the same, irrespective of the colour. The table below shows the percentage of marbles of each colour used in the current design. The cost of each marble increased by 25%. Therefore, the designer decided to reduce equal numbers of marbles of each colour to keep the total cost unchanged. What is the percentage of blue marbles in the new design?
- 10Aptitude · 2 marks · MCQ · ModerateP, Q, R and S crossed a lake in a boat that can hold a maximum of two persons, with only one set of oars. The following additional facts are available.
(i) The boat held two persons on each of the three forward trips across the lake and one person on each of the two return trips.
(ii) P is unable to row when someone else is in the boat.
(iii) Q is unable to row with anyone else except R.
(iv) Each person rowed for at least one trip.
(v) Only one person can row during a trip.
- 111 mark · MCQ · EasyA single-phase 100kVA, 1000V/100V, 50Hz transformer has a voltage drop of 5% across its series impedance at full load. Of this, 3% is due to resistance. The percentage regulation of the transformer at full load with 0.8 lagging power factor is
- 121 mark · MCQ · EasyIn a salient pole synchronous motor, the developed reluctance torque attains the maximum value when the load angle in electrical degrees is
- 141 mark · MCQ · ModerateFour power semiconductor devices are shown in the figure along with their relevant terminals. The device(s) that can carry dc current continuously in the direction shown when gated appropriately is (are)
- 151 mark · MCQ · ModerateTwo wattmeter method is used for measurement of power in a balanced three-phase load supplied from a balanced three-phase system. If one of the wattmeters reads half of the other (both positive), then the power factor of the load is
- 161 mark · MCQ · ModerateConsider a lossy transmission line with V1 and V2 as the sending and receiving end voltages, respectively. Z and X are the series impedance and reactance of the line, respectively. The steady-state stability limit for the transmission line will be
- 171 mark · MCQ · EasyThe graph of a network has 8 nodes and 5 independent loops. The number of branches of the graph is
- 181 mark · MCQ · ModerateIn the figure, the voltages are v1(t)=100cos(ωt), v2(t)=100cos(ωt+π/18) and v3(t)=100cos(ωt+π/36). The circuit is in sinusoidal steady state, and R≪ωL. P1, P2 and P3 are the average power outputs. Which one of the following statements is true?

- 191 mark · MCQ · EasyMatch the transfer functions of the second-order systems with the nature of the systems given below.
- 201 mark · MCQ · ModerateA positive charge of 1nC is placed at (0,0,0.2) where all dimensions are in metres. Consider the x−y plane to be a conducting ground plane. Take ϵ0=8.85×10−12F/m. The z component of the E field at (0,0,0.1) is closest to
- 211 mark · MCQ · ModerateLet f be a real-valued function of a real variable defined as f(x)=x2 for x≥0, and f(x)=−x2 for x<0. Which one of the following statements is true?
- 221 mark · MCQ · ModerateThe value of the directional derivative of the function Φ(x,y,z)=xy2+yz2+zx2 at the point (2,−1,1) in the direction of the vector p=i+2j+2k is
- 231 mark · MCQ · ModerateThe value of the integral ∮Cz2−4z+1dz in counter clock wise direction around a circle C of radius 1 with center at the point z=−2 is
- 241 mark · MCQ · EasyIn the logic circuit shown in the figure, Y is given by

- 251 mark · MCQ · ModerateThe op-amp shown in the figure is ideal. The input impedance iinvin is given by
- 261 mark · MCQ · EasyA continuous-time input signal x(t) is an eigenfunction of an LTI system, if the output is
- 271 mark · NAT · ModerateConsider a non-singular 2×2 square matrix A. If trace(A)=4 and trace(A2)=5, the determinant of the matrix A is ____ (up to 1 decimal place).
- 281 mark · NAT · ModerateLet f be a real-valued function of a real variable defined as f(x)=x−[x], where [x] denotes the largest integer less than or equal to x. The value of ∫0.251.25f(x)dx is ____ (up to 2 decimal places).
- 291 mark · NAT · ModerateIn the two-port network shown, the h11 parameter (where, h11=I1V1, when V2=0) in ohms
is ____________ (up to 2 decimal places).
- 301 mark · NAT · EasyThe series impedance matrix of a short three-phase transmission line in phase coordinates is ZsZmZmZmZsZmZmZmZs. If the positive sequence impedance is (1+j10)Ω, and the zero sequence is (4+j31)Ω, then the imaginary part of Zm (in Ω) is ____ (up to 2 decimal places).
- 311 mark · NAT · ModerateThe positive, negative and zero sequence impedances of a 125MVA, three-phase, 15.5kV, star-grounded, 50Hz generator are j0.1pu, j0.05pu and j0.01pu respectively on the machine rating base. The machine is unloaded and working at the rated terminal voltage. If the grounding impedance of the generator is j0.01pu, then the magnitude of fault current for a b-phase to ground fault (in kA) is ________ (up to 2 decimal places).
- 321 mark · NAT · EasyA 1000×1000 bus admittance matrix for an electric power system has 8000 non-zero elements. The minimum number of branches (transmission lines and transformers) in this system are _____ (up to 2 decimal places).
- 331 mark · NAT · ModerateThe waveform of the current drawn by a semi-converter from a sinusoidal AC voltage source is shown in the figure. If I0=20A, the rms value of fundamental component of the current is ________ A (up to 2 decimal places).
- 341 mark · NAT · ModerateA separately excited dc motor has an armature resistance Ra=0.05Ω. The field excitation is kept constant. At an armature voltage of 100V, the motor produces a torque of 500Nm at zero speed. Neglecting all mechanical losses, the no-load speed of the motor (in radian/s) for an armature voltage of 150V is ____ (up to 2 decimal places).
- 351 mark · NAT · EasyConsider a unity feedback system with forward transfer function given by
- 362 marks · MCQ · ModerateA transformer with toroidal core of permeability μ is shown in the figure. Assuming uniform flux density across the circular core cross-section of radius r≪R, and neglecting any leakage flux, the best estimate for the mean radius R is
- 372 marks · MCQ · ModerateA 0−1Ampere moving iron ammeter has an internal resistance of 50mΩ and inductance of 0.1mH. A shunt coil is connected to extend its range to 0−10Ampere for all operating frequencies. The time constant in milliseconds and resistance in mΩ of the shunt coil respectively are
- 382 marks · MCQ · ModerateThe positive, negative and zero sequence impedances of a three phase generator are Z1,Z2 and Z0 respectively. For a line-to-line fault with fault impedance Zf, the fault current is If1=kIf, where If is the fault current with zero fault impedance. The relation between Zf and k is
- 392 marks · MCQ · ModerateConsider the two bus power system network with given loads as shown in the figure. All the values shown in the figure are in per unit. The reactive power supplied by generator G1 and G2 are QG1 and QG2 respectively. The per unit values of QG1, QG2, and line reactive power loss (Qloss) respectively are
- 402 marks · MCQ · ModerateThe per-unit power output of a salient-pole generator which is connected to an infinite bus, is given by the expression, P=1.4sinδ+0.15sin2δ, where δ is the load angle. Newton-Raphson method is used to calculate the value of δ for P=0.8pu. If the initial guess is 30∘, then its value (in degree) at the end of the first iteration is
- 412 marks · MCQ · ModerateA DC voltage source is connected to a series L-C circuit by turning on the switch S at time t=0 as shown in the figure. Assume i(0)=0, v(0)=0. Which one of the following circular loci represents the plot of i(t) versus v(t) ?
- 422 marks · MCQ · ModerateThe equivalent impedance Zeq for the infinite ladder circuit shown in the figure is
- 432 marks · MCQ · ModerateConsider a system governed by the following equations
- 442 marks · MCQ · HardThe number of roots of the polynomial, s7+s6+7s5+14s4+31s3+73s2+25s+200, in the open left half of the complex plane is
- 452 marks · MCQ · ModerateIf C is a circle ∣z∣=4 and f(z)=(z2−3z+2)2z2, then ∮Cf(z)dz is
- 462 marks · MCQ · ModerateWhich one of the following statements is true about the digital circuit shown in the figure
- 472 marks · MCQ · EasyDigital input signals A,B,C with A as the MSB and C as the LSB are used to realize the Boolean function F=m0+m2+m3+m5+m7, where mi denotes the ith minterm. In addition, F has a don't care for m1. The simplified expression for F is given by
- 482 marks · MCQ · ModerateConsider the two continuous-time signals defined below:
- 492 marks · MCQ · ModerateThe signal energy of the continuous-time signal
x(t)=[(t−1)u(t−1)]−[(t−2)u(t−2)]−[(t−3)u(t−3)]+[(t−4)u(t−4)] is
- 502 marks · NAT · ModerateThe Fourier transform of a continuous-time signal x(t) is given by
X(ω)=(10+jω)21,−∞<ω<∞, where j=−1 and ω denotes frequency. Then the
value of ∣lnx(t)∣ at t=1 is ____ (up to 1 decimal place). (\ln denotes the
logarithm to base e )
- 512 marks · NAT · HardIn the circuit shown in the figure, the bipolar junction transistor (BJT) has a current gain β=100. The base-emitter voltage drop is a constant, VBE=0.7V. The value of the Thevenin equivalent resistance RTh (in Ω) as shown in the figure is ____ (up to 2 decimal places).
- 522 marks · NAT · ModerateAs shown in the figure, C is the arc from the point (3,0) to the point (0,3) on the circle x2+y2=9. The value of the integral ∫C(y2+2yx)dx+(2xy+x2)dy is ____ (up to 2 decimal places).
- 532 marks · NAT · EasyLet f(x)=3x3−7x2+5x+6. The maximum value of f(x) over the interval [0,2] is ____ (up to 1 decimal place).
- 542 marks · NAT · ModerateLet A=1−10020−10−2 and B=A3−A2−4A+5I, where I is the 3×3 identity matrix. The determinant of B is ____ (up to 1 decimal place).
- 552 marks · NAT · ModerateThe capacitance of an air-filled parallel-plate capacitor is 60pF. When a dielectric slab whose thickness is half the distance between the plates, is placed on one of the plates covering it entirely, the capacitance becomes 86pF. Neglecting the fringing effects, the relative permittivity of the dielectric is ______ (up to 2 decimal places).
- 562 marks · NAT · EasyThe unit step response y(t) of a unity feedback system with open loop transfer function
G(s)H(s)=(s+1)2(s+2)K
is shown in the figure. The value of K is ____ (up to 2 decimal places).
- 572 marks · NAT · ModerateA three-phase load is connected to a three-phase balanced supply as shown in the figure. If Van=100∠0∘V, Vbn=100∠−120∘V and Vcn=100∠−240∘V (angles are considered positive in the anti-clockwise direction), the value of R for zero current in the neutral wire is ____________ Ω (up to 2 decimal places).
- 582 marks · NAT · ModerateThe voltage across the circuit in the figure, and the current through it, are given by the following expressions:
- 592 marks · NAT · ModerateA phase controlled single phase rectifier, supplied by an AC source, feeds power to an R-L-E load as shown in the figure. The rectifier output voltage has an average value given by Vo=2πVm(3+cosα), where Vm=80πvolts and α is the firing angle. If the power delivered to the lossless battery is 1600W, α in degree is_____ (up to 2 decimal places).
- 602 marks · NAT · ModerateThe figure shows two buck converters connected in parallel. The common input dc voltage for the converters has a value of 100V. The converters have inductors of identical value. The load resistance is 1Ω. The capacitor voltage has negligible ripple. Both converters operate in the continuous conduction mode. The switching frequency is 1kHz, and the switch control signals are as shown. The circuit operates in the steady state. Assuming that the converters share the load equally, the average value of iS1, the current of switch S1 (in Ampere), is ____ (up to 2 decimal places).
- 622 marks · NAT · ModerateA 200V DC series motor, when operating from rated voltage while driving a certain load, draws 10A current and runs at 1000r.p.m. The total series resistance is 1Ω. The magnetic circuit is assumed to be linear. At the same supply voltage, the load torque is increased by 44%. The speed of the motor in r.p.m. (rounded to the nearest integer) is ____.
- 632 marks · NAT · ModerateA dc to dc converter shown in the figure is charging a battery bank, B2 whose voltage is constant at 150V. B1 is another battery bank whose voltage is constant at 50V. The value of the inductor, L is 5mH and the ideal switch, S is operated with a switching frequency of 5kHz with a duty ratio of 0.4. Once the circuit has attained steady state and assuming the diode D to be ideal, the power transferred from B1 to B2 (in Watt) is ____ (up to 2 decimal places).
- 642 marks · NAT · ModerateThe equivalent circuit of a single phase induction motor is shown in the figure, where the parameters are R1=R2′=Xl1=Xl2′=12Ω, XM=240Ω and s is the slip. At no-load, the motor speed can be approximated to be the synchronous speed. The no-load lagging power factor of the motor is ________ (up to 3 decimal places).
- 652 marks · NAT · ModerateThe voltage v(t) across the terminals a and b as shown in the figure, is a sinusoidal voltage having a frequency ω=100radian/s. When the inductor current i(t) is in phase with the voltage v(t), the magnitude of the impedance Z (in Ω) seen between the terminals a and b is ______ (up to 2 decimal places).