28 questions0 / 28 done
- 1CE 2024 Set 1 · 1 mark · MCQ · EasyThe three-dimensional state of stress at a point is given by
σ=10000400000MPa.
The maximum shear stress at the point is
- 2CE 2024 Set 1 · 1 mark · MCQ · ModerateConcrete of characteristic strength 30MPa is required. If 40 specimens of concrete cubes are to be tested, the minimum number of specimens having at least 30MPa strength should be
- 3CE 2024 Set 1 · 1 mark · MCQ · EasyConsider the statements P and Q.
- 4CE 2024 Set 1 · 1 mark · MCQ · ModerateThe following figure shows the arrangement of formwork for casting a cantilever RC beam.
- 5CE 2024 Set 1 · 1 mark · MSQ · EasyThe elements that DO NOT increase the strength of structural steel are
- 6CE 2024 Set 1 · 1 mark · MSQ · ModerateConsider a balanced doubly-reinforced concrete section. If the material and other sectional properties remain unchanged, for which of the following cases will the section becomes under-reinforced?
- 7CE 2024 Set 1 · 1 mark · NAT · ModerateThe plane frame shown in the figure has fixed support at joint A, hinge support at joint F, and roller support at joint I. In the figure, A to I indicate joints of the frame.
- 8CE 2024 Set 1 · 2 marks · MCQ · ModerateFind the correct match between the plane stress states and the Mohr’s circles.
- 9CE 2024 Set 1 · 2 marks · MCQ · HardThe beam shown in the figure is subjected to a uniformly distributed downward load of intensity q between supports A and B.
- 10CE 2024 Set 1 · 2 marks · MCQ · ModerateA homogeneous shaft PQR with fixed supports at both ends is subjected to a torsional moment T at point Q, as shown in the figure. The polar moments of inertia of the portions PQ and QR of the shaft with circular cross-sections are J1 and J2, respectively. The torsional moment reactions at the supports P and R are TP and TR, respectively.
- 11CE 2024 Set 1 · 2 marks · NAT · HardThe plane truss shown in the figure has 13 joints and 22 members. The truss is made of a homogeneous, prismatic, linearly elastic material. All members have identical axial rigidity. A to M indicate the joints of the truss. The truss has pin supports at joints A and L and roller support at joint K. The truss is subjected to a 10kN vertically downward force at joint H and a 10kN horizontal force in the rightward direction at joint B as shown.
- 12CE 2024 Set 1 · 2 marks · NAT · ModerateAn inverted T-shaped concrete beam (B1) in the figure, with centroidal axis X−X, is subjected to an effective prestressing force of 1000kN acting at the bottom kern point of the beam cross-section. Also consider an identical concrete beam (B2) with the same grade of concrete but without any prestressing force.
- 13CE 2024 Set 1 · 2 marks · NAT · ModerateThe initial cost of an equipment is Rs.1,00,000. Its salvage value at the end of accounting life of 5 years is Rs.10,000. The difference in depreciation (in Rs.) computed using ‘double-declining balance method’ and ‘straight line method’ of depreciation in Year-2 is ____ (in positive integer).
- 14CE 2024 Set 1 · 2 marks · NAT · EasyA slab panel with an effective depth of 250mm is reinforced with 0.2% main reinforcement using 8mm diameter steel bars. The uniform center-to-center spacing (in mm) at which the 8mm diameter bars are placed in the slab panel is ____ (rounded off to the nearest integer).
- 15CE 2024 Set 2 · 1 mark · MCQ · ModerateA 3m long, horizontal, rigid, uniform beam PQ has negligible mass. The beam is subjected to a 3kN concentrated vertically downward force at 1m from P, as shown in the figure. The beam is resting on vertical linear springs at the ends P and Q. For the spring at the end P, the spring constant KP=100kN/m.
- 16CE 2024 Set 2 · 1 mark · MCQ · EasyConsider the statements P and Q.
- 17CE 2024 Set 2 · 1 mark · MCQ · HardFor a thin-walled section shown in the figure, points P, Q , and R are located on the major bending axis X−X of the section. Point Q is located on the web whereas point S is located at the intersection of the web and the top flange of the section.
- 18CE 2024 Set 2 · 1 mark · MCQ · EasyConsider the following data for a project of 300 days duration.
- 19CE 2024 Set 2 · 1 mark · MCQ · ModerateA simply supported, uniformly loaded, two-way slab panel is torsionally unrestrained. The effective span lengths along the short span (x) and long span (y) directions of the panel are lx and ly, respectively. The design moments for the reinforcements along the x and y directions are Mux and Muy, respectively. By using Rankine-Grashoff method, the ratio Mux/Muy is proportional to
- 20CE 2024 Set 2 · 1 mark · MCQ · EasyThe structural design method that DOES NOT take into account the safety factors on the design loads is
- 21CE 2024 Set 2 · 1 mark · NAT · ModerateThe steel angle section shown in the figure has elastic section modulus of 150.92cm3 about the horizontal X−X axis, which passes through the centroid of the section.
- 22CE 2024 Set 2 · 2 marks · MCQ · ModerateA linearly elastic beam of length 2l with flexural rigidity EI has negligible mass. A massless spring with a spring constant k and a rigid block of mass m are attached to the beam as shown in the figure.
- 23CE 2024 Set 2 · 2 marks · MCQ · ModerateA critical activity in a project is estimated to take 15 days to complete at a cost of Rs. 30,000. The activity can be expedited to complete in 12 days by spending a total amount of Rs. 54,000. Consider the statements P and Q.
- 24CE 2024 Set 2 · 2 marks · MCQ · ModerateA homogeneous, prismatic, linearly elastic steel bar fixed at both the ends has a slenderness ratio (l/r) of 105, where l is the bar length and r is the radius of gyration. The coefficient of thermal expansion of steel is 12×10−6/∘C. Consider the effective length of the steel bar as 0.5l and neglect the self-weight of the bar.
- 25CE 2024 Set 2 · 2 marks · NAT · ModerateFor the 6m long horizontal cantilever beam PQR shown in the figure, Q is the mid-point. Segment PQ of the beam has flexural rigidity EI=2×105kN⋅m2 whereas the segment QR has infinite flexural rigidity. Segment QR is subjected to uniformly distributed, vertically downward load of 5kN/m.
- 26CE 2024 Set 2 · 2 marks · NAT · EasyThe horizontal beam PQRS shown in the figure has a fixed support at point P, an internal hinge at point Q, and a pin support at point R. A concentrated vertically downward load (V) of 10kN can act at any point over the entire length of the beam.
- 27CE 2024 Set 2 · 2 marks · NAT · ModerateA concrete column section of size 300mm×500mm as shown in the figure is subjected to both axial compression and bending along the major axis. The depth of the neutral axis (Xu) is 1.1 times the depth of the column, as shown.
- 28CE 2024 Set 2 · 2 marks · NAT · ModerateThe table shows the activities and their durations and dependencies in a project.