16 questions0 / 16 done
- 1CE 2024 Set 1 · 1 mark · MCQ · EasyA 2m wide strip footing is founded at a depth of 1.5m below the ground level in a homogeneous pure clay bed. The clay bed has unit cohesion of 40kPa. Due to seasonal fluctuations of water table from peak summer to peak monsoon period, the net ultimate bearing capacity of the footing, as per Terzaghi's theory, will
- 2CE 2024 Set 1 · 1 mark · MCQ · EasyConsider the statements P and Q.
- 3CE 2024 Set 1 · 1 mark · NAT · EasyAn embankment is constructed with soil by maintaining the degree of saturation as 75% during compaction. The specific gravity of soil is 2.68 and the moisture content is 17% during compaction. Consider the unit weight of water as 10kN/m3. The dry unit weight (in kN/m3) of the compacted soil is ____ (rounded off to 2 decimal places).
- 4CE 2024 Set 1 · 2 marks · MCQ · EasyA vertical smooth rigid retaining wall is supporting horizontal ground with dry cohesionless backfill having a friction angle of 30∘. The inclinations of failure planes with respect to the major principal plane for Rankine’s active and passive earth pressure conditions, respectively, are
- 5CE 2024 Set 1 · 2 marks · MSQ · HardWhich of the following statement(s) is/are CORRECT?
- 6CE 2024 Set 1 · 2 marks · NAT · ModerateThe total primary consolidation settlement (Sc) of a building constructed on a 10m thick saturated clay layer is estimated to be 50mm. After 300days of the construction of the building, primary consolidation settlement was reported as 10mm. The additional time (in days) required to achieve 50% of Sc will be ____ (rounded off to the nearest integer).
- 7CE 2024 Set 1 · 2 marks · NAT · ModerateAn infinite slope is made up of cohesionless soil with seepage parallel to and up to the sloping surface. The angle of slope is 30∘ with respect to horizontal ground surface. The unit weights of the saturated soil and water are 20kN/m3 and 10kN/m3, respectively.
- 8CE 2024 Set 1 · 2 marks · NAT · HardA soil sample was consolidated at a cell pressure of 20kPa and a back pressure of 10kPa for 24hours during a consolidated undrained (CU) triaxial test. The cell pressure was increased to 30kPa on the next day and it resulted in the development of pore water pressure of 1kPa. The soil sample failed when the axial stress was gradually increased to 50kPa. The pore water pressure at failure was recorded as 21kPa. The value of Skempton's pore pressure parameter B for the soil sample is ____ (rounded off to 2 decimal places).
- 9CE 2024 Set 2 · 1 mark · MCQ · ModerateThe contact pressure distribution shown in the figure belongs to a
- 10CE 2024 Set 2 · 1 mark · MCQ · ModerateWhich one of the following saturated fine-grained soils can attain a negative Skempton's pore pressure coefficient (A)?
- 11CE 2024 Set 2 · 1 mark · NAT · EasyA reinforced concrete pile of 10m length and 0.7m diameter is embedded in a saturated pure clay with unit cohesion of 50kPa. If the adhesion factor is 0.5, the net ultimate uplift pullout capacity (in kN) of the pile is ____ (rounded off to the nearest integer).
- 12CE 2024 Set 2 · 2 marks · MCQ · EasyConsider the statements P and Q related to the analysis/design of retaining walls.
- 13CE 2024 Set 2 · 2 marks · MSQ · ModerateConsider the statements P, Q , and R.
- 14CE 2024 Set 2 · 2 marks · NAT · ModerateA homogeneous earth dam has a maximum water head difference of 15m between the upstream and downstream sides. A flownet was drawn with the number of potential drops as 10 and the average length of the element as 3m. Specific gravity of the soil is 2.65. For a factor of safety of 2.0 against piping failure, void ratio of the soil is ____ (rounded off to 2 decimal places).
- 15CE 2024 Set 2 · 2 marks · NAT · ModerateThe in-situ percentage of voids of a sand deposit is 50%. The maximum and minimum densities of sand determined from the laboratory tests are 1.8g/cm3 and 1.3g/cm3, respectively. Assume the specific gravity of sand as 2.7.
- 16CE 2024 Set 2 · 2 marks · NAT · ModerateA drained triaxial test was conducted on a saturated sand specimen using a stress-path triaxial testing system. The specimen failed when the axial stress reached a value of 100kN/m2 from an initial confining pressure of 300kN/m2.